Monday, March 14, 2011

Bonnet Tutorial

This bonnet is great to cover your newborn's head, for a baptizing ceremony (like I used it) or for a dress-up bin. This is a pretty simple bonnet but my problem was the lack of a pattern. I knew how I would construct it but what pieces to cut? So I tried constructing my own pattern and it worked! I will give you my pattern, which was made to fit Kitten's head when she was 18 months old and her head circumference was 18 inches (I know, she has a small head, for an average baby it will probably be a newborn size). I will also explain how to draw your own pattern.

What you will need - 1/3 yard of exterior fabric, 1/4 yard of lining fabric, 1 yard of ribbon, thread. The amount of fabric will depend on your size but this should be plenty. Allow extra for one way design fabric.

1. Cut out pieces according to pattern: from exterior fabric cut 1 back (pattern, 1/4" SA - seam allowance included), 1 side (cut 4.5" by 16.5" (1/4" SA included) and optionally cut off all angles according to the diagram - 1/2" from short sides and 4.25" from long sides) and 1 ruffle (24.5" by 3.75", 3/8 SA included) pieces; from lining fabric cut 1 back and 1 side pieces, from ribbon or other cord cut 2 pieces as long as would like your ties to be (you can always trim later, so better leave some extra length). I advise you to cut 1 back and 1 side piece from other fabric, sew them together as in step 3 and try it on your child. It does not take long but you may find out that you need to make adjustments, since every head is different.
Disregard the pieced pieces, I was running out of fabric
2. If you need a different size of bonnet, lay your child with her back of the head on a piece of paper and quickly, before she rans away, trace the head, holding your pencil almost perpendicular to the paper (if you angle it toward the head you will have too much of a difference between front width and back width, which will make for a difficult shaping and lots of adjustments). Measure the distance between crown of the head and how low you want your bonnet to be and draw the bottom accordingly. Add seam allowances along all edges. Cut out (it is best to fold the pattern in half and cut a symmetrical piece) and see how it looks on your child's head. If it seems to be about right, measure the circumference of the rounded part and this will be the length of the side piece. Its width will depend on your child's measurement - measure from the back of the head to approximately hairline or where you want your bonnet to end (remember to count for a ruffle if you are making one). Add seam allowances to the width (they are already added for length since you measured it from the back piece). I chose to make the ends narrower, so that it fits the curve of the head better, but you may skip that, I don't believe it made that much of a difference. I just pinched the side while Kitten was wearing it to see how much width I like to subtract and them made it a gradual symmetrical transition. I ended up subtracting 1/2" from top and bottom of the short sides and 4.25" form both ends of the long side, see the pattern, it is much clearer in drawing. For the ruffle (although you can omit it if you like) I multiplied the length of the side piece by 1.5, if you want a fuller ruffle, you may multiply by 2. For the width, decide how wide you want your ruffle to be, add seam allowance (I recommend at least 3/8") and multiply by 2. If you are making your own pattern, it is especially important to make a muslin.
    3. Pin the side piece to the back piece right sides facing. Pin the center and bottoms first and see how much fabric you have left. I wanted to have a couple of tucks in the back, so I spaced them evenly around the center back (fold in half to find the center) and just played with them until their width was about the same. Stitch. Repeat for the lining.


    4. Pin the lining to the exterior along the bottom edge right sides facing, aligning side seams and pinning ribbons in between and directed inside the bonnet. Leave at least your seam allowance and a little more between ribbon and side. Stitch, making sure not to catch extra ribbon in your stitching.


    5. To make a ruffle, fold the ruffle piece in half lengthwise right sides facing and stitch together 2 short sides. Trim the corners. Turn the right side out and press. Stitch 2 rows of longest stitch (leave long tail on both sides), I do one 1/4" from the edge and the second one between the edge and the first row. Make sure they do not cross each other! Next, tie top and bottom threads of both rows on one end. 


    6. Find the middle and quarters on your bonnet and ruffle and pin the ends and those places ONLY to the exterior fabric. Ruffle should be facing away from the front and be attached to the right side of the exterior fabric. Grab the two top threads of the ruffle and pull gently, easing fabric along the threads. Keep pulling and sliding until the length of your ruffle matches the length of the bonnet front. Spread the gathers so that all quarter sections are even. Stitch in place 1/2" away from the edge, so that gathering stitches are enclosed.


    7. Turn down the seam allowance on the lining and hand stitch in place, encasing the ruffle seam allowance. Top stitch along the bonnet face opening.


    Please tell me if there are any questions or something is unclear. The explanation is long and it probably sounds more complicated that it actually is, but believe me, this is really easy. If you make a bonnet using this pattern, please send me a link, I would love to see it.

      17 comments:

      1. Julie,

        I think you left most of us speechless! :D I will show you this post next time when you will dare to say that you lack creativity (and your other posts) ;))

        ReplyDelete
      2. Yeah, I actually wanted to ask you to try to make it and tell me if there are any mistakes ;)

        ReplyDelete
      3. I can't seem to download the pattern. It keeps saying the link isn't valid. Help please?

        ReplyDelete
      4. Could you email the pattern to me? Thanks

        ReplyDelete
      5. Lovely bonnet!
        Pattern link says it's not available. Please email pattern to me.
        Thanks

        ReplyDelete
      6. Please could you email pattern to me at preciousdelilah@icloud.com thank you
        Is there all different sizes

        ReplyDelete
      7. Are you anywhere near Fort Worth? I would love to share my sewing room with you!

        ReplyDelete
      8. Can you please email me the pattern lanceandbronia@gmail.com

        ReplyDelete
      9. Could you email me the pattern please? Abunt@yahoo.com

        ReplyDelete
      10. Please
        Email me the pattern at diamonddi0464@sbcglobal.net

        ReplyDelete
      11. Can you please email the pattern and sizes please... cl_kwiss@hotmail.com ty

        ReplyDelete
      12. What a beautiful bonnet.

        ReplyDelete
      13. Would you be able to email me the pattern please as link is unavailable
        susie.k.young@gmail.com

        Thanks

        ReplyDelete
      14. I would like to make this. Could you send me the pattern , please. Thank you. assofamily@yahoo.com

        ReplyDelete